This causes a peak at the cutoff frequency that is most X/Y Control - Horizontal - Filter cutoff frequency (the filter is of the low pass type), Vertical - Resonance.When set low, only the lower frequencies will be heard. When set to the highest frequency this meansĪll frequencies can be heard. Low Pass filters allow frequencies below the cutoff frequency to pass. MiniSynth uses a single Low Pass filter with cutoff and resonance controls. Release - Time taken to fall from the Sustain level to zero when the key is released.Decay - Time taken to go from the maximum level to the Sustain level.Attack - Time taken for the filter to reach the maximum level.To better understand ADSR controls it's useful to have in mind that for any note there are three basic timing events, 'note on' event, 'note hold time' and 'note off' event. You release the key or to soften the attack of a sound, for example. These controls are how you would make a note play on after The ADSR envelope provides a volume envelope (volume changes) at key on, key held and key release.
#Detune pc download mod#
Amount - Multiplier for the Mod wheel effect.LFO - Modulation will affect the LFO speed.Filter - Modulation will affect the filter cutoff.NOTE: Mod Wheel is only available when a MOD Wheel MIDI controller is connected. Mod Wheel - Select Modulation targets.Slide (portamento) effect and then add it where you want by holding the previous note before playing the next. This allows you to play normal lead melodies without the Lead - A monophonic mode where auto-portamento is enabled (when notes overlap) and the envelopes are not retrigged.Mono - A monophonic mode (one note playback), slides always sound on note changes and envelopes reset.Voice Mode - Polyphony (ability to play more than one note) and voice transitions.Noise - Adds white noise (hiss) into the mix.Modifier - Action depends on the selected waveform type, see above.Transpose - Transpose the oscillator +/- 12 semitones.Spread 2 - 3 Saw waves at 0 octave (root), 5th and +1 octave intervals.Spread 1 - 3 Saw waves at -1 octave, 0 octave (root) and +1 octave intervals.Modifier - Adjusts phase shift of the Saw waves relative to each other creating a 'comb filter' effect. DeafSaw - Two Saws with same frequency.Modifier - adds in additional spectral frequencies.
SuperSaw - 8 Saw waves panned in the stereo field.Modifier controls pitch of second square +/- 24 semitones. Square + Square - Pair of Square waveforms.Modifier controls pitch of the saw +/- 24 semitones. Modifier controls pulse width of the waveform so that at 0 or 100% there is complete phase cancellation. Modifier controls pitch of the second saw +/- 24 semitones. Modifier controls pulse width of the Square wave, so in positions 0 or 100 pulse width becomes zero and a perfect Saw Saw - A Saw + Square wave of the same frequency and phase.Depending on the selection there are some unique behavior of the voices. Oscillator - Controls for the waveform shape and pitch.Some waveform modes areĭual-voice where two waveforms are mixed. MiniSynth has an advanced multi-mode oscillator that changes architecture depending on the waveform selection. Oscillators are the sound source for the synth. TIP: Create patches using MiniSynth in FL Studio and save them for use in FL Studio Mobile, so you can take the same sounds on the road with you.Ĭontrols are spread across 6 tabs making them perfect for touch-screen control. MiniSynth is also included with FL Studio MobileĪnd is used when converting FL Studio Mobile projects to FL Studio format.Įven if you don't use FL Studio Mobile, you will find MiniSynth a great addition to your library and you can still share patches with FL Studio Mobile users on the
#Detune pc download how to#
There are 6 tabs covering the synthesizer controls making it perfect when working with a touch interface (for which it was designed) or for the new user learning how to program synthesizers. MiniSynth is a fully featured synthesizer with a low processor overhead and great sound.
0 kommentar(er)
